Authoritative definitions of the International System of Units and SI prefixes.
Unit conversion
Metres per second squared to Gal Converter
1 m/s² = 100 Gal. Enter a value to convert m/s² to Gal, then use the formula and table below. Displayed digits may be rounded.
Speed & accelerationInstant result
Decimals
Formula result = input × 1 ÷ 0.01. 1 m/s² = 100 Gal
Nonzero results too small for the selected decimal places use scientific notation.
Nonzero results too small for the selected decimal places use scientific notation.
Common examples
One value, several units
Centimetres per second squared100 cm/s²
Feet per second squared3.2808 ft/s²
Gal100 Gal
Standard gravity0.102 g₀
Conversion table
| m/s² | Gal |
|---|---|
| 1 m/s² | 100 Gal |
| 2 m/s² | 200 Gal |
| 5 m/s² | 500 Gal |
| 10 m/s² | 1,000 Gal |
| 25 m/s² | 2,500 Gal |
| 50 m/s² | 5,000 Gal |
| 100 m/s² | 10,000 Gal |
Conversion chart
1 m/s²100 Gal
5 m/s²500 Gal
10 m/s²1,000 Gal
25 m/s²2,500 Gal
50 m/s²5,000 Gal
Worked example
1 m/s² = 100 Gal. Apply the selected conversion formula to other input values.
Unit definition
Metres per second squared (m/s²) One metres per second squared equals 1 metre per second squared.
Unit history
Metres per second squared is represented here using its modern SI definition or an internationally accepted relationship to an SI base unit.
Step by step
1. Parse the value, including fractions.
2. Convert m/s² to metre per second squared.
3. Convert the base value to Gal and apply your display precision.
Understand the result before using it
Metres per second squared to Gal converts a value measured in Metres per second squared (m/s²) into the equivalent value in Gal (Gal). The numerical value changes because the size and definition of the selected unit changes; the underlying quantity does not.
Calculated result
The conversion follows the displayed unit relationship. Display rounding can hide additional digits, and measured inputs cannot become more accurate merely by changing units.
Formula, assumptions, and example
Formula
result = input × 1 ÷ 0.01
Assumptions
- Metres per second squared and Gal represent the same acceleration quantity.
- The input is expressed in m/s²; the output is expressed in Gal.
- The unit definitions and conventional relationship shown on this page apply.
Worked example
1 m/s² = 100 Gal. For another value, apply the same relationship and round only to the precision your source measurement supports.
When to use it
Good uses
- Read a m/s² measurement in a document that expects Gal.
- Compare a metres per second squared value with a value reported in gal.
- Check the m/s² to Gal arithmetic before copying the result into another calculation.
Limitations
Common mistakes to avoid
- Mach varies with the local speed of sound; this tool uses the representative condition stated beside the converter.
- Round the output to a precision justified by the original measurement.
- Verify safety-critical, regulated, laboratory, and contractual conversions against the controlling standard.
Sources and further reading
These references explain the underlying standards or provide authoritative context. Your own contract, institution, clinician, product documentation, local code, or governing standard may be the controlling source.
Guidance on unit names, symbols, conversions, and numerical presentation.
Questions about this calculation
How do I convert Metres per second squared to Gal?
result = input × 1 ÷ 0.01. Input is in m/s²; result is in Gal. 1 m/s² = 100 Gal. The displayed digits may be rounded.
What is 1 m/s² in Gal?
1 m/s² = 100 Gal. The displayed digits may be rounded.
Can I reverse the m/s² to Gal conversion?
Yes. Swap the source and target units in the converter. The reverse relationship converts Gal back to m/s².
Is the Metres per second squared to Gal result exact?
The conversion follows the displayed unit relationship. Display rounding can hide additional digits, and measured inputs cannot become more accurate merely by changing units.